|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
VSS�SR - SURROUND
Early Bal (-100dB R, Center, -100dB L) the left/right balance of the Early Reflections. Allows you to offset the Early Reflections from the normal center position. Hi Color (±50) Adjusts the spectral balance of the Early Type. The Hi Color parameter is actually an advanced Hi Cut parameter. The default setting of this parameter is customized to each of the Early Types. Lo Cut (20 - 400Hz) This adjustable filter removes low frequencies for the Early Reflections. Hi Decay (0.01 - 2.5) Multiplier for the frequencies above the Hi Xover frequency. Example: If the main Decay parameter is set to 2.0 sec and the Hi Decay parameter is set to 1.5, frequencies above the Hi-Xover will decay for 3.0 sec. Conversely if this parameter is set to 0.5 the Decay time above the Hi Xover point will be 1 sec. Hi Xover (500Hz - 20kHz) sets the frequency at which the transition from the mid frequencies to the high frequencies takes place. Mid Decay (0.01 - 2.5) The Ratio control multiplier for the mid frequencies. This parameter is normally set to 1.0 as it is the main parameter adjusted by the main Decay parameter. This mid-range decay control would normally be omitted, however, TC Engineers felt you could use this parameter as a fine adjustment tool to �tweak� a preset to sound just right without having to adjust the master Decay parameter. Mid Xover (200Hz - 2kHz) Sets the frequency at which the transition from the low-mid to the mid frequencies takes place. Lo mid Decay (0.01 - 2.5) The Ratio control multiplier for the low-mid frequencies Lo Xover (20Hz - 500Hz) Sets the frequency at which the transition from the low to the low-mid frequencies takes place. Lo Decay (0.01 - 2.5) The Ratio control multiplier for the low frequencies. Lo Damp Freq (20Hz - 200Hz) Sets the Lo Cut frequency for the next parameter, Lo Damp. Use these two parameters to take away any objectionable low frequencies entering the Reverb tail processor. Lo Damp (-18dB - 0dB) Sets the amount of cut in dBs. Used with the previous parameter, Lo Damp Freq.
Reverb Tail
Rev Type (Smooth, Natural, Metal, Fast, Fast WD) Adjust this parameter with the Early Lev turned all the way off and the Rev Lev all the way up. Change the type to get a feel of what each one sounds like. Rev Depth With this parameter you can change the depth of the reverb tail. Diffuse (±50) This parameter gives you more or less diffusion than the algorithm designer intended for the given Decay time. For optimum performance the diffusion is automatically adjusted behind the scenes whenever you change decay times. This parameter gives you the added control to vary the diffusion around this automatic setting. Hi Cut (20 - 20kHz) Rolls off the top end as it enters the Reverb tail. Used in conjunction with Hi Soften and Hi Decay to "darken" a room. Hi Soften (+/-50) Hi Soften is a special filter used to "soften" the high frequencies of Reverb tail. This is not a simple Hi Cut filter but a complex set of filters working together to remove those frequencies that make a reverb sound "brittle" or harsh sounding. Hi Soften is scaled/linked to the Hi Cut and Hi Decay parameters.
43
|
|
|
> |
|
